国产男女性做爽歪歪爱视频,亚洲一二三,欧美在线视频一区二区,亚洲欧美日本综合一区二区三区,日日操天天操,天天噜日日噜,看全色黄大色黄大片免责看的

Hi!Welcome to Taian Demei Electromechanical Equipment Co.,Ltd.!
Taian Demei Electromechanical Equipment Co.,Ltd.

Focusing on the field of temperature calibration experimental equipment production

DY-69 High Precision Digital Thermometer

DY-69 High Precision Digital Thermometer

DY-69 High Precision Digital Thermometer

◇ Product Introduction ◇ Product Features◇ Technical Indicator

[Product Introduction]

Performance and Characteristics

? 1. Handheld thermometer

? 2. High accuracy, 0.002 | t | for measuring temperature (t)

? 3. The high resolution, 0.01 ℃

? 4. Wide measuring range, is - 50 ~ 450 ℃

? 5. The response speed

? 6. Data function

? 7. Sheath maerial can rotate 90 degrees, is suitable for industrial site complex environment

? 8. Micro power consumption, battery life 600 hours (excluding backlight)

Steps

① Press the power button, the power on display HELLO, after 2S display the measured temperature;

② After the temperature is stable, press the data lock key to lock the data, and the backlight is turned on at the same time;

(3) After the measurement, turn off the data lock function, and then turn off the power supply;

Note: In order to prolong the battery life of DY-69 high-precision digital thermometer, please turn off the power of the product as soon as possible after use.

DY-69 High Precision Digital Thermometer

Method of measurement

(1) in order to measure accurately, the probe rod insertion depth must be greater than the lower limit insertion depth: 160℃ below the lower limit insertion depth of 70mm;

The lower limit insertion depth above 160℃ is 120mm;

(2) In order to prevent the damage of high temperature to the plastic shell and internal electronic components, the depth of the probe rod insertion must be less than the upper limit of insertion depth: below 160℃ the upper limit of insertion depth is 75mm smaller than the total length of the probe rod;

The upper limit of insertion depth above 160℃ is 150mm less than the total length of the probe rod.

Use the Calibration Function

① clean the back cover screw sealant, open the shell;

② Put the probe rod in a standard 0℃ environment (such as water triple point bottle). After the display data is stable, the 0℃ calibration can be completed by touching the S3 button lightly.

The position of S3 keys is shown in the figure below;

③ Assemble the shell.

DY-69 High Precision Digital Thermometer

Product maintenance

①Clean the probe rod: please use a soft cloth and alcohol to clean;

② Replace the battery: when the boot has been displayed "HELLO" or the above words appear in the measurement process, it indicates that the battery power is insufficient to be replaced, pay attention to the battery polarity, do not reverse.

Matters needing attention

? do not use this product is used to measure the temperature of dangerous charged components

? unless 0 ℃ calibration need, please do not open the product case

? please be sure to replace the battery in no explosion hazard places

? replacement battery to choose correct battery model

? if you do not use this product for a long time, please take out the battery

? this product shell plastic material is qualitative, use process please do not touch

Common Fault

Fault SymptomReason Analysis Treatment measures
The boot always displays HELLO or the above words appear in the process of useBattery under voltageReplacement battery
Measurement inaccuracyInsufficient depth of insertionAdjust the insertion depth
Always display -50.0 or display garbled code after bootTemperature sensing element connection failure or circuit board failureContact the manufacturer

Selection Table

DY-69 High Precision Digital Thermometer

DY-69 High Precision Digital Thermometer

DY-69 High Precision Digital Thermometer 2020-12-9 This article was read 7049 Times
Previous:DY-HT3F-D Split portable high temperature short cavity blackbody furnaceNext:DY-HT3F-D Split portable high temperature short cavity blackbody furnace

Technical

Contact us

Taian Demei Electromechanical Equipment Co.,LTD.

Address:Building A8,No.98, South Nianhua Street,Shengzhuang Town,Taishan District,Tai'an City,Shandong Province,China

Tel: +86-538-6518288

Contact: Fred Xu   Email: fred@dmthermo.com

Mobile/Wechat/Whatsapp: +86 15966019173



Taian Demei Electromechanical Equipment Co.,LTD.             Lu ICP No. 14019246-4             Publicity

灵川县| 白银市| 旅游| 河曲县| 宁海县| 集贤县| 紫阳县| 徐州市| 连云港市| 邛崃市| 资阳市| 乌什县| 和静县| 乐昌市| 五家渠市| 勐海县| 明星| 浪卡子县| 晋宁县| 金寨县| 迁西县| 威远县| 虹口区| 陇南市| 石棉县| 家居| 邓州市| 临西县| 永安市| 宝清县| 花垣县| 扶风县| 辰溪县| 钟祥市| 中宁县| 彩票| 娄烦县| 陵川县| 新郑市| 宾川县| 普安县|